New Sig!

[93zm6tally]

Until Jan 24th.

[Slow ET]

Very nice, whats the 60'.

[93zm6tally]

Very nice, whats the 60'.

1.73 with a good amount of spin. The new clutch is putting much more torque to the ground. I also short shifted staying off of the rev-lmiter, but I really need a shift light. Also ran a 12.47 when I tried moving the shift point up too much. I'm going to get the rev-limiter set higher and will use results from next weeks dyno to get an optimum shift point.

[slmdLS1]

very nice!!! your stroker and heavier mods gonna be done before jan 24th i assume?




ps. fall asleep at the tree again? :mrgreen:

[93zm6tally]

very nice!!! your stroker and heavier mods gonna be done before jan 24th i assume?




ps. fall asleep at the tree again? :mrgreen:

No not really, but I did manage to roll through the staging lights like a dick. I'm always a little nervous on the first run. Still cut a 12.7 and a 1.8 60. Traction really wasn't that great last night, it never rained but there was a constant mist, even Tony was pissed about it.

[93zm6tally]

And I'll hopefully order the stroker in January, but it will probably be two months after that before I see it.

[Gt]

Ya, Traction sucked ass last night. No matter how much I slip'd the clutch. I was spinning. Hell, I even spun on the 3-4 shift :(.

best outta 5 passes:

2.25 60'
5.950 330
8.984 1/8
81.04 mph
11.591 1000'
13.797 1/4
102.16 mph

Tony

[97ChameleonTA]

Congrats on the new best, great times! And a great MPH too. What are your mods?

Marty

[slmdLS1]

what'd greg run?

[brandboZ28]

13.08 @113 I think

[93zm6tally]

Congrats on the new best, great times! And a great MPH too. What are your mods?

Marty


Pretty similar to your sig. Headers are Hookers and I don't have a Meziere. I also have locally ported and polished heads, but I don't think they are exactly what I'd call done really well. Oh and I have a 12 bolt with 4.11's

[T]

good job gramps

[jlaw]

Very nice, Mark. Congrats.

You know traction sucked when CLUTCH-SLIP MASTER could only pull a 2.25 60'

[93zm6tally]

Yeah with my new clutch I'm cutting the same 60ft time as I did last time at Gainesville. Difference is I've got a lot more wheelspin even with the tires heated up. I'm hoping to help some of that with new LCA's and brackets and a new Torque Arm

[97ChameleonTA]

Pretty similar to your sig. Headers are Hookers and I don't have a Meziere. I also have locally ported and polished heads, but I don't think they are exactly what I'd call done really well. Oh and I have a 12 bolt with 4.11's

Damn! :-o

Is that with the stock cam too? Or have you done any weight reduction? That is a smokin' MPH!

Marty

[93zm6tally]

Pretty similar to your sig. Headers are Hookers and I don't have a Meziere. I also have locally ported and polished heads, but I don't think they are exactly what I'd call done really well. Oh and I have a 12 bolt with 4.11's

Damn! :-o

Is that with the stock cam too? Or have you done any weight reduction? That is a smokin' MPH!

Marty

No. CM Motorsports 227/233 .567/.569(I think)

[slmdLS1]

the purple people eater!!!
http://www.stang.cc/tmcaalbums/Track-Pics/Mark.jpg

[Greg Kulbick]

Yeah, 13.08 @ 113. On my fourth pass I was spinning on the big end so I parked it. Shitty 60's too. I'll have to wait until January for 12's. :(

[slmdLS1]

how did the n2o usage go? this bottle better than the Vause's one?

[Greg Kulbick]

Much better, I was still able to get over 1000 psi with the heater after two passes as opposed to only being able to get 800 after two passes last time.