Newbie

[Blwn04]

Tallahassee is da bomb! I went to FSU (until they kicked me out!) for a couple of party filled semesters a few years back. Had to come back to P'cola where I finished up college. Anyway I drive a 04 Cobra with a few mods. Plan on adding some blower cams in the near future for an extra 60-75 ponies of kick!

[J8127]

what it is

[fatkid]

:yikes: look at those numbers. Damn man!!!! Any pics of the car???? And welcome

[Blwn04]

Thanks, I need to fix a small problem and the power should increase a tad. Here are some pics.........

[fatkid]

What have u run??

[Bullhead00]

Welcome!! Sounds like a bad ride you have there. "Say hello to Mr. Bell!"

[Blwn04]

What have u run??

Well I have only ran it once at the track with the new setup. I was trying to run in the 7.5 class in the 1/8 and was trying to sandbag my times. Ran 3 times letting off at the end which were coming up in the 7.2xx area at 96-98. Since I couldn't get the sandbag down, I decided to goes balls out on my forth run and smoked the clutch to the point I had to replace it. I just installed a 26 spline input shaft, Fidanza Flywheel, Center Force Dual Puck yesterday and hope to have it broke in by Sunday when I can run it again. My driving skills are not the best, but I bet a decent driver could get it in the 6.xx area. I am hoping for a 10 sec 1/4 mile pass when I get a chance to make it to a 1/4 track.

[Z06BoZ]

welcome,did ur clutch burn up when u were staging doin a burnout?I sent u a PM about the BAP by the way.

[Slush Box]

Welcome man the KB is sweet.

[Blwn04]

The clutch decided it didn't like the pwr coming out of the hole in first, then reminded me how it didn't like it while shifting to 2nd so I let out of it shifting to 3rd and it smoked all the way down the track and smelled of burnt clutch for a week. I could drive it, just couldn't punch it in 1st, 2nd, or 3rd without it slipping. I don't remember a pm about a BAP. I also have a line lock going in to take some of the heat off the rear brakes and clutch well doing my burnout.

[Blwn04]

Welcome man the KB is sweet.

Thanks, I believe they make one for an Explorer! :P

[Z06BoZ]

Oh i sent u one on SS maybe it didnt go through i just wanted to know how hard it is to install the BAP,i have to get mine in so i can get ready for james to tune it.Hes really really hard to get a hold of and that maf i got from granalli? or something he said its special and has to be tuned by him. Also u think u can help me install the blower?

[TurboL67]

Welcome, Tim! When are you gonna let me drive that beast??


Oh, Im back in town for the weekend and will be at holt on sunday if it's open.

[Blwn04]

I will have to check SS, I don't visit it to much. The BAP is easy to install, just make sure you use the pressure switch that comes with it. You can run it behind your glove box and "T" it into your stock boost line. I'm not sure when I can help with the blower, I have been pretty maxed lately. Thought Andrew was helping you do that for a blower or something? If your going to run any kind of high boost, you better get that clutch setup on order now or the new power will be useless.

[Z06BoZ]

ill just send u a pm on here

[Blwn04]

Welcome, Tim! When are you gonna let me drive that beast??


Oh, Im back in town for the weekend and will be at holt on sunday if it's open.

Lets hope the rain stays away Sunday! We can run them if you want....
:twisted:

[ju015dd]

that is one sweet ride man, the snakes are taking over! :jaw:

[boostedsvt]

damn fords!!! :finger:

[slmdLS1]

welcome to the boards, nice ride!!